Venturi RDA by Neovapetek – Kayfun as RDA

Venturi Clone in stock for $12.09

The Venturi RDA is an interesting design based on the Kayfun in several ways. The idea here was to rebuild the Kayfun as a dripping atomizer. By adapting this design, Neovapetek are going for flavor for sure. The Venturi prices out at the higher end of the price spectrum, but you get a lot of stuff for your money here as it comes with 3 different top caps for customizing the look. The Venturi is a 22mm RDA so it will fit flush with most conventional 18650/18450/18350 22mm mods.

The Venturi comes in a standard, 3 post design that accommodates dual and quad coil builds. As mentioned it comes with 3 different top caps, all with unique designs. This allows you to customize the look of your Venturi and change it as you desire. The RDA comes in 3 sections, the deck, aforementioned top cap choices and an inner chimney which is what makes this similar to the Kayfun.

The Venturi features a standard adjustable 510 connection (with a 22k gold plated post to increase connectivity) and is made in the USA.

What makes the Venturi RDA unique?

The unique part of the design here is the inner sleeve/chimney. Air flow actually starts at the top of the outer cap near the drip tip. Air is pushed down and enters the inner sleeve/chimney. The inner sleeve/chimney is shaped in an hourglass fashion that allows for a much smaller coil chamber which pushes the airflow up into a secondary top chamber just beneath where your drip tip will attach. This is done to somewhat mimic the air chamber on the Kayfun, but as an RDA this gives you a lot more options. If you’re familiar with the RJ Mods Cats RDA – this is a similar design. Also like the Cats – this design GREATLY reduces leaking problems native to RDA’s in general. You can get a lot of juice in here and don’t have to worry about it leaking out the holes. Also a nice plus are the deep juice wells. This is an RDA that’s meant to hold a lot of juice.

You have adjustable airflow which is a huge step up from the Kayfun. Now remember the Kayfun is a tank device. Its one of the best available, but one of my biggest gripes is that the airflow is pretty tight. Its not a lung hit device by any means. The Kayfun has many restrictions being a tank design which may very well have inspired Neovapetek to use this design in and RDA. The smaller chamber is not typical for RDA devices either. This will keep the air compressed at the coils and results in a warmer, more concentrated vapor production which, in theory, increases vapor and enhances flavor. This is what sets the Venturi apart from other RDA’s on the market.

Also nice is the lack of any logos or branding on the outside of this RDA. Its a really clean looking device no matter what outer cap you decide to go with. This is a big plus. If you like minimal design this is a nice device. The top caps are individually labeled and all look different. The “Stratis” offers a nice conical look. The “Brake” takes a nod from the Tobh with the top fins. The “Classic” sits somewhere between the two. Think a taller Stratis with the Tobh fins you see on the Brake cap. All three caps look minimal and beautiful on just about any mod you put them on. I should also note that the packaging is beautiful. Another plus to Neovapetek on the presentation.

Should I buy the Venturi?

If you are a flavor kind of person this is going to be for you – no question. This is quite a wonderful RDA. Its well built, made in the USA and is a beautiful design. If you like options on your RDA’s this is also a good buy as Neovapetek are also making optional top caps in various metals including copper and brass. I imagine this design will yield even more customizable options in the future.

Also the entire design is really easy to clean and build on. Most of the parts seem to be replaceable so this is an RDA that will last you a while.

Venturi Clone in stock for $12.09

Also be sure to check out the Plume Veil from Aethertech